首页 > Multi Functional Dynamic Data Acquisition Device
相关项目
相关产品
Multi Functional Dynamic Data Acquisition Device
Multi Functional Dynamic Data Acquisition Device

 

(1) Signal Chain

Consider implementing "true synchronization" for the four channels of a single board, using independent signal processing and ADC acquisition for each channel. The gain of each channel can be configured separately. In addition, for low-power versions of cloud intelligent vibration acquisition devices, external ICP, IEPE, and 4-20mA current type sensors are not currently considered. Current type sensors are all considered to be equipped with external conditioning boxes.

The anti aliasing filter adopts an active filter design. Although the Δ - ∑ type ADC has the function of oversampling and extraction, which reduces the requirements for external anti aliasing filters, in order to ensure the performance of the filter transition band, the external active filter design scheme is continued, and the filter order is set to 6.

(2) Data Collection Process

After the data of the first group of four channels is collected by the ADC, the FPGA caches the first group of four channel data collected by the ADC in the internal RAM, and first performs digital filtering according to the sampling rate configuration. After completion, it is stored in the ping pong cache's PING. When the data in the PING is full (note that the system's data is also being collected and digitally filtered at this time), the second group of data begins to be stored in the PONG, and the data in the PING needs to be sent out before the PONG is full at this time. Although data is described as "groups", the actual process is continuous, and each group of data will be packed into a data packet during transmission.

It is necessary to consider that the sampling rate of each channel is different, such as 1K and 2K sampling. Currently, Cortex-A8 applications have been implemented.

(3) External Interface

Reserved GPS external antenna interface for receiving GPS second pulse signals and UTC time information.

Reserved external analog/digital signal triggering interfaces are used to monitor two types of signals through internal switching. In addition, the analog triggering level is optimized from manually setting sliding resistors to programmable resistors. External analog and digital triggers can be triggered by external analog or digital signal sensors, such as temperature, vibration, shock, etc., for physical signal triggering sampling.

Note that in addition to external signal triggers, there should also be built-in digital triggers. Digital triggers are used by the data acquisition device to judge data while it is in operation. If the data exceeds the threshold set by the upper computer software, it will be displayed and stored. At the same time, the firmware of the single board should also consider this function. The acquisition trigger signal of the single board is triggered by external physical signals.

(4) Peripherals and Interfaces

The system uses two IO extenders with IIC communication mode, which are respectively used to configure the working mode of PGA and ADC. The IIC controller is Cortex-A8.

EEPROM is used to store configuration information and onboard information of a single board. During the device's power on initialization process, the configuration information in EEPROM is configured to ADC and PGA through FPGA and IO expander.

RTC clock is used to provide accurate real-time clock for the single board, and the calibration of this clock can be synchronized through the UTC time of the built-in GPS.

External triggering of data collection requires consideration of configurable collection time, and specific configurable parameters should be selected based on the actual memory size. The data is stored on an SD card. Assuming that the device has a data volume of 100K per second, a 1GB card can continuously store data for more than 2 and a half hours. At the same time, important data backup needs to be considered, similar to the gravity sensing emergency backup function of a driving recorder. You can consider activating the emergency backup function in the event of external communication interruption, and communication can be normal without the need for it.

The GPS module and DTU module both use onboard methods, and it is necessary to consider the fixing method, EMC design, etc.

Ethernet is considered for wired communication methods, with functionalityThrough internal configuration, data exchange can be carried out with two data links of DTU.

(5) System Power Supply

Due to the low-power design of the system, it is considered to use a single power supply for the entire signal chain, which can save DC-DC losses and reduce the power consumption of the analog circuit by half.

Each signal chain considers independent electronic switches for power control. For example, when working on channels 1, 2, and 3, in addition to the ADC turning off the 4th channel POWERDOWN, it is also necessary to cut off the power supply of the signal chain to further reduce power consumption. When the system is not working in continuous sampling mode, the entire analog circuit part of the single board enters a power-off state to minimize system power consumption.

Other peripherals such as GPS, DTU, etc. can consider using electronic switches for sleep and wake-up control to reduce the power consumption of the system during sleep mode.

The system is equipped with a built-in lithium battery, which is charged through an external solar panel or charger. The power module is responsible for monitoring and protecting the lithium battery.

*本公司产品技术参数及配置如有变更,恕不另行通知

Copyright © 2026 All Rights Reserved 版权所有· 江西飞尚科技有限公司      备案号:赣ICP备13000994号-1     许可证编号:赣B2-20230512
技术支持:
专属客服
专属微信客服